Xmotorstore Payments
Malossi front shock absorber Rs24 wheelbase 180 mm 4614236
Malossi code: 4614236
Rs24 front Malossi shock absorber, 180 mm wheelbase for 10" wheel.
The versatility of this suspension has proven surprising thanks to the 3 new adjustment systems, which enhance its use on the road and track:
-adjustment of the hydraulic system in extension to absorb all the roughness of the terrain;
-double regulation of the hydraulic compression system (separate for low and high speed);
-spring preload to adapt the vehicle's running position;
- setup variation system for cornering behaviour.
Technical features
These special shock absorbers have technical characteristics that represent the maximum technological expression available on the market today:
-Type: hydropneumatic shock absorber with separate compensation tank
-Use: racing scooter
-Shock absorber rod Ø 14 mm in 38 NiCrMo4UNI 7845 hardened and tempered steel with hard chrome deposit 25-30 micron thick (surface hardness of the shaft not yet treated HRC 55/60)
-Piston Ø 36 mm with two independent disc packs, one in compression and one in extension
-New lamellar system in harmonic steel which allows for very precise calibration
-Piston guide shoe of the LUBRIFLON-PTFEB70 type (bronze filled modified compound)
- Sliding on DU GUIDE bush (compound obtained by sintering a state of spheroidal bronze on a suitably pressed mild steel strip and with subsequent impregnation and coating with a mixture of PTFE+FB)
- Scraper ring in SEALTHANE grade 9345 polyester resin
-Micrometic adjustment of spring pre-load via ring nuts
-Adjustment of hydraulic braking in extension pre-selectable on approximately 24 positions
-Double adjustment of the hydraulic compression braking, pre-selectable on approximately 10 positions each, separate for low and high speed
-Special oil with low viscosity and practically insensitive to temperature variations
-External compensation tank which allows an increase in the quantity of internal fluids
- Wheelbase adjustment of 25 mm (only for rear shock absorber)
- Wheelbase: rear 321 + 25 mm - front 181 mm
-Stroke: rear 62 mm - front 45 mm
Malossi shock absorber for:
Malossi shock absorber for PIAGGIO QUARTZ 50 2T LC. The pair of PIAGGIO shock absorbers 4614479 is also available.
Malossi shock absorber for PIAGGIO ZIP SP 50 2T LC 2001 onwards. The pair of PIAGGIO shock absorbers 4614479 is also available.
Malossi shock absorber for PIAGGIO ZIP SP 50 2T LC up to 2000. The pair of PIAGGIO shock absorbers 4614479 is also available.
Reference: 143.755.014+143.755.015
Brand: POLINI
Pair of Polini 910 Rs minimoto fork legs. Kit consisting of: 143.755.015 left fork leg minibike Polini 910 Rs. 143.755.014 fork stem right minimoto Polini 910 Rs.
Reference: 01.AS.0314.L
Brand: Ohvale
Ohvale Max jet 120 Code: 01.AS.0314.L
Reference: 5519425B
Brand: Malossi
Malossi Injtronic 5519425B electronic control unit Code: 5519425B Malossi Injtronic electronic control unit for original cylinder. The Injtronic engine control unit is the natural evolution of the original Piaggio system and allows the vehicle's performance to be increased. The use of a latest generation 32-bit microprocessor, in synergy with hardware...
Reference: 206.0351
Brand: POLINI
Polini segment diameter 47,6x0x8 mm chromed 206.0351 Polini segment for: Aprilia, Aprilia Area 51, Aprilia Gulliver 50 Lc, Aprilia Rally 50 LC, Aprilia Sonic 50 GP, Aprilia Sr 50, Aprilia Mojito 50, Benelli, Benelli 491 50, Benelli K2 50 liquid cooled, Beta, Beta Ark 50 , Beta Eikon 50, Derbi, Derbi Gp1 50, Gilera, Gilera Dna 50, Gilera Easy Moving 50,...
Reference: 248.113
Brand: POLINI
Polini belt for Piaggio Ciao with variator Polini Code: 248.113
Reference: 6118814
Brand: Malossi
Malossi K-DRIVE z28 sprocket Malossi code: 6118814 Malossi sprocket for YAMAHA T MAX 560 ie 4T LC euro 5 2020-2021 (J420E). Malossi sprocket for YAMAHA T MAX 560 ie 4T LC euro 5 2022. Malossi sprocket for YAMAHA T MAX Tech MAX 560 ie 4T LC euro 5 2020-2021 (J420E). Malossi sprocket for YAMAHA T MAX Tech MAX 560 ie 4T LC euro 5 2022.
Reference: 5514747
Brand: Malossi
Lambda emulator TC UNIT O2 Malossi controller 5514747 Code: 5514747 To further optimize carburetion and transient performance, the use of the O2 controller is recommended. In the latest generation motorbikes, the control unit, thanks to the lambda probe, is able to correct the quantity of fuel that must be injected so that the carburetion is constant,...
Reference: 5113597
Brand: Malossi
Malossi Multivar 2000 variator 5113597 Code: 5113597 Multivar 2000 When technology makes the difference. Multivar: the sports change with burning acceleration that does not give space! A jewel to be set in your scooter. Too bad that it cannot be exhibited, it is so perfect! Designed by highly experienced engineers, produced in full in the Malossi...
Reference: 6215023BB
Brand: Malossi
Malossi brake pads Malossi code: 6215023BB Malossi brake pads for MBK SKYCRUISER 125 ie 4T LC euro 3. Front. Malossi brake pads for YAMAHA X MAX 125 ie 4T LC until 2008. Front. Malossi brake pads for YAMAHA X MAX 125 ie 4T LC from 2009 to 2013. Front. Malossi brake pads for YAMAHA X MAX 250 4T LC. Front. Malossi brake pads for YAMAHA X MAX 250 ie 4T LC...
Reference: Molle.rac.cs
Brand: CS Racing
Cs muffler exhaust fitting springs. Short cs minibike muffler springs, these springs are applied between the "cylinder" connection and the exhaust manifold. Attention: pair of springs, specific for Cs minibike muffler. Total spring length 35 mm. Unloaded spring length (L0) 32 mm. Spring length without eyelet (Lk) 17 mm. External diameter of the coils (De)...
Reference: 66 4696.J0
Brand: Malossi
2 Malossi rollers d.3x9.8 MBK/Peugeot GR1 Malossi code: 66 4696.J0 Malossi rollers for MBK 51 V 50 (AV 10) Replacement for CYLINDER KIT 31 6105: production discontinued. Malossi rollers for PEUGEOT 103 104 105 50 2T Replacement for CYLINDER KIT 31 6104 and CYLINDER 31 6757: production discontinued. Malossi rollers for PEUGEOT 103 RCX 50 Replacement for...
Reference: 6215029BB
Brand: Malossi
Malossi brake pads Malossi code: 6215029BB Malossi brake pads for MBK SKYLINER 250 4T LC Front for vehicles produced from 2000. Malossi brake pads for YAMAHA MAJESTY 250 4T LC Front for vehicles produced from 1996. Malossi brake pads for YAMAHA MAJESTY 400 4T LC Front for vehicles with double front disc up to 2008. Malossi brake pads for YAMAHA MAJESTY...
Reference: 01.TE.0026.L
Brand: Ohvale
Ohvale GP-0 and GP-2 chassis and body clip kit. Ohvale code: 01.TE.0026.L
Reference: 6219288
Brand: Malossi
Brake disc kit external diameter 250 thickness 3 mm increased with caliper support bracket for original fork Malossi code: 6219288 Malossi brake lever for MBK NITRO 50 2T LC Front for vehicles produced 1997. Malossi brake lever for YAMAHA AEROX 50 2T LC euro 0-1 Front. Malossi brake lever for YAMAHA AEROX 50 2T LC euro 2 Front.
Malossi front shock absorber Rs24 wheelbase 180 mm 4614236
Malossi code: 4614236
Rs24 front Malossi shock absorber, 180 mm wheelbase for 10" wheel.
The versatility of this suspension has proven surprising thanks to the 3 new adjustment systems, which enhance its use on the road and track:
-adjustment of the hydraulic system in extension to absorb all the roughness of the terrain;
-double regulation of the hydraulic compression system (separate for low and high speed);
-spring preload to adapt the vehicle's running position;
- setup variation system for cornering behaviour.
Technical features
These special shock absorbers have technical characteristics that represent the maximum technological expression available on the market today:
-Type: hydropneumatic shock absorber with separate compensation tank
-Use: racing scooter
-Shock absorber rod Ø 14 mm in 38 NiCrMo4UNI 7845 hardened and tempered steel with hard chrome deposit 25-30 micron thick (surface hardness of the shaft not yet treated HRC 55/60)
-Piston Ø 36 mm with two independent disc packs, one in compression and one in extension
-New lamellar system in harmonic steel which allows for very precise calibration
-Piston guide shoe of the LUBRIFLON-PTFEB70 type (bronze filled modified compound)
- Sliding on DU GUIDE bush (compound obtained by sintering a state of spheroidal bronze on a suitably pressed mild steel strip and with subsequent impregnation and coating with a mixture of PTFE+FB)
- Scraper ring in SEALTHANE grade 9345 polyester resin
-Micrometic adjustment of spring pre-load via ring nuts
-Adjustment of hydraulic braking in extension pre-selectable on approximately 24 positions
-Double adjustment of the hydraulic compression braking, pre-selectable on approximately 10 positions each, separate for low and high speed
-Special oil with low viscosity and practically insensitive to temperature variations
-External compensation tank which allows an increase in the quantity of internal fluids
- Wheelbase adjustment of 25 mm (only for rear shock absorber)
- Wheelbase: rear 321 + 25 mm - front 181 mm
-Stroke: rear 62 mm - front 45 mm
