- Reduced price
- New

Xmotorstore Payments
Malossi front shock absorber RS24 for Piaggio 4614236
Malossi code: 4614236
Rs24 front Malossi shock absorber, 180 mm wheelbase for 10" wheel.
The versatility of this suspension has proven surprising thanks to the 3 new adjustment systems, which enhance its use on the road and track:
-adjustment of the hydraulic system in extension to absorb all the roughness of the terrain;
-double regulation of the hydraulic compression system (separate for low and high speed);
-spring preload to adapt the vehicle's running position;
- setup variation system for cornering behaviour.
Technical features
These special shock absorbers have technical characteristics that represent the maximum technological expression available on the market today:
-Type: hydropneumatic shock absorber with separate compensation tank
-Use: racing scooter
-Shock absorber rod Ø 14 mm in 38 NiCrMo4UNI 7845 hardened and tempered steel with hard chrome deposit 25-30 micron thick (surface hardness of the shaft not yet treated HRC 55/60)
-Piston Ø 36 mm with two independent disc packs, one in compression and one in extension
-New lamellar system in harmonic steel which allows for very precise calibration
-Piston guide shoe of the LUBRIFLON-PTFEB70 type (bronze filled modified compound)
- Sliding on DU GUIDE bush (compound obtained by sintering a state of spheroidal bronze on a suitably pressed mild steel strip and with subsequent impregnation and coating with a mixture of PTFE+FB)
- Scraper ring in SEALTHANE grade 9345 polyester resin
-Micrometic adjustment of spring pre-load via ring nuts
-Adjustment of hydraulic braking in extension pre-selectable on approximately 24 positions
-Double adjustment of the hydraulic compression braking, pre-selectable on approximately 10 positions each, separate for low and high speed
-Special oil with low viscosity and practically insensitive to temperature variations
-External compensation tank which allows an increase in the quantity of internal fluids
- Wheelbase adjustment of 25 mm (only for rear shock absorber)
- Wheelbase: rear 321 + 25 mm - front 181 mm
-Stroke: rear 62 mm - front 45 mm
Malossi shock absorber for:
Malossi shock absorber for PIAGGIO QUARTZ 50 2T LC. The pair of PIAGGIO shock absorbers 4614479 is also available.
Malossi shock absorber for PIAGGIO ZIP SP 50 2T LC 2001 onwards. The pair of PIAGGIO shock absorbers 4614479 is also available.
Malossi shock absorber for PIAGGIO ZIP SP 50 2T LC up to 2000. The pair of PIAGGIO shock absorbers 4614479 is also available.
Reference: 4614479
Brand: Malossi
Pair of front and rear shock absorbers Malossi Rs24 4614479 for Piaggio Malossi code: 4614479 Pair of Malossi shock absorbers, front wheelbase 180 mm and rear wheelbase 290 mm 10" tire shock absorbers These special shock absorbers have technical characteristics that represent the maximum technological expression available on the market today: -Type:...
Reference: 4615153B
Brand: Malossi
Attack kit for Malossi front shock absorber 4615153B Malossi code: 4615153B.
Reference: 4615154B
Brand: Malossi
Malossi coaxial compression adjustment kit 4615154B Malossi code: 4615154B
Reference: 4615151B
Brand: Malossi
Malossi complete rod for front shock absorber 4615151B Malossi code: 4615151B.
Reference: 1115148b
Brand: Malossi
Malossi gasket kit complete for shock absorbers RS24 / 10 / 10 - R Malossi code: 1115148b
Reference: 3415191B
Brand: Malossi
Malossi piston kit for shock absorber 3415191B Malossi code: 3415191B. Piston diameter 36 mm with guide shoe of the type LUBRIFLON PTFEB70 (modified compound loaded bronze).
Reference: 02 2913B
Brand: Malossi
Malossi intake manifold 20x24 mm 02 2913B Code: 02 2913B Malossi intake manifold for Phbg and Shb carburetors
Reference: 248.119
Brand: POLINI
Polini variator belt for Kymco Agility 125 Code: 248.119 Application: Kymco, Kymco People 125/125 GTi 4V / 150/150 E4, Kymco Vivio 125/150 air, Kymco Agility 125/150 / 200i, Kymco Movie 125/150, Kymco Super 8 125, Kymco Like 125/200 i, Malaguti, Malaguti Ciak 125/150/200
Reference: 202.1370
Brand: POLINI
Polini primary gear for Yamaha Minarelli Z13-44. Polini Code: 202.1370
Reference: 166.0083/12
Brand: POLINI
Polini thermal unit kit 166.0083/12 Code: 166.0083/12 Polini cylinder kit for Yamaha-Aprilia Sr h2o, Malaguti f12 Lc Diameter 47mm 12mm plunger
Reference: 06 7874B
Brand: Malossi
Malossi O-ring diameter 63.22x1.78 mm for heads diameter 57.5 - 61 Malossi code: 06 7874B
Reference: FT-4161
Brand: Ohvale
Sintered Ohvale Gp-0 front brake pads. Sintered front pads for Ohvale Gp-0, racing compound, suitable for long-term training and racing use. Ohvale brake pads with performance equal to the originals. ATTENTION: Pads not approved for CIV.
Reference: 01.IF.0067.L
Brand: Ohvale
Ohvale Kit membrane Code: 01.IF.0067.L
Reference: 250.025
Brand: POLINI
Polini clutch bell for Piaggio Gilera Evolution 2 model 107 mm diameterCode 250.025This Polini clutch bell is compatible as an original spare.Diameter: 107 mmWeight: 464 grApplication: Aprilia, Aprilia Scarabeo 50 2T Street restyling / 50 4T 4V / 50 4T 2V Restyling / 100 2T, Aprila SR 50 2T R / 50 4T Motard 4V, Aprilia Sportcity one 50 4T 2V / 50 4T 4V,...
Reference: 3111248
Brand: Malossi
Malossi cylinder diameter 63 in aluminum H2O 4T Malossi code: 3111248 Malossi cylinder for Benelli Velvet 125 4T LC. Malossi cylinder for Benelli Velvet 150 4T LC (Yamaha). Malossi cylinder for Italjet Jupiter 125 4T LC. Malossi cylinder for Italjet Jupiter 150 4T LC. Malossi cylinder for Italjet Millennium 125 4T LC. Malossi cylinder for Italjet...
Reference: 03.PE.0031.L
Brand: Ohvale
Ohvale reverse electronic shift rod complete. Code: 03.PE.0031.L Compatibility: Ohvale Gp-0 reverse electronic shift rod. Ohvale Gp-2 reverse electronic shift rod.
Reference: 01.RP.0023.L
Brand: Ohvale
Front wheel Ohvale bearing from 2021 Code: 01.RP.0023.L
Reference: 144.705.004
Brand: POLINI
Polini 3G clutch jaws series Code: 144.705.004 Set of jaws for Polini minicross 3G racing mini-motard clutch
Reference: 6215018BS
Brand: Malossi
Malossi MHR Synt approved brake pads Malossi code: 6215018BS Malossi brake pads for HONDA @ 125 4T LC Front for vehicles produced 2000 APPROVED Malossi brake pads for HONDA @ 150 4T LC Front for vehicles produced 2000 APPROVED Malossi brake pads for HONDA PS 125 ie 4T LC euro 3 Front APPROVED Malossi brake pads for HONDA PS 150 ie 4T LC euro 3 Front...
Reference: 01.SB.0205.L
Brand: Ohvale
Ohvale Gasket assy cylinder head Code: 01.SB.0205.L
Reference: 144.065.002
Brand: POLINI
Polini water pump oil seal 8x16x10
Reference: GHR 066.001 - 143.270.016
Brand: GHR
Rubber intake manifold Ghr diameter 21 mm. Specific manifold for minibikes with Ghr engine and phbg carburettor.
Malossi front shock absorber RS24 for Piaggio 4614236
Malossi code: 4614236
Rs24 front Malossi shock absorber, 180 mm wheelbase for 10" wheel.
The versatility of this suspension has proven surprising thanks to the 3 new adjustment systems, which enhance its use on the road and track:
-adjustment of the hydraulic system in extension to absorb all the roughness of the terrain;
-double regulation of the hydraulic compression system (separate for low and high speed);
-spring preload to adapt the vehicle's running position;
- setup variation system for cornering behaviour.
Technical features
These special shock absorbers have technical characteristics that represent the maximum technological expression available on the market today:
-Type: hydropneumatic shock absorber with separate compensation tank
-Use: racing scooter
-Shock absorber rod Ø 14 mm in 38 NiCrMo4UNI 7845 hardened and tempered steel with hard chrome deposit 25-30 micron thick (surface hardness of the shaft not yet treated HRC 55/60)
-Piston Ø 36 mm with two independent disc packs, one in compression and one in extension
-New lamellar system in harmonic steel which allows for very precise calibration
-Piston guide shoe of the LUBRIFLON-PTFEB70 type (bronze filled modified compound)
- Sliding on DU GUIDE bush (compound obtained by sintering a state of spheroidal bronze on a suitably pressed mild steel strip and with subsequent impregnation and coating with a mixture of PTFE+FB)
- Scraper ring in SEALTHANE grade 9345 polyester resin
-Micrometic adjustment of spring pre-load via ring nuts
-Adjustment of hydraulic braking in extension pre-selectable on approximately 24 positions
-Double adjustment of the hydraulic compression braking, pre-selectable on approximately 10 positions each, separate for low and high speed
-Special oil with low viscosity and practically insensitive to temperature variations
-External compensation tank which allows an increase in the quantity of internal fluids
- Wheelbase adjustment of 25 mm (only for rear shock absorber)
- Wheelbase: rear 321 + 25 mm - front 181 mm
-Stroke: rear 62 mm - front 45 mm