- Reduced price
- New

Xmotorstore Payments
Pair of front and rear shock absorbers Malossi Rs24 4614479 for Piaggio
Malossi code: 4614479
Pair of Malossi shock absorbers, front wheelbase 180 mm and rear wheelbase 290 mm
10" tire shock absorbers
These special shock absorbers have technical characteristics that represent the maximum technological expression available on the market today:
-Type: hydropneumatic shock absorber with separate compensation tank
-Use: racing scooter
-Shock absorber rod Ø 14 mm in 38 NiCrMo4UNI 7845 hardened and tempered steel with hard chrome deposit 25-30 micron thick (surface hardness of the shaft not yet treated HRC 55/60)
-Piston Ø 36 mm with two independent disc packs, one in compression and one in extension
-New lamellar system in harmonic steel which allows for very precise calibration
-Piston guide shoe of the LUBRIFLON-PTFEB70 type (bronze filled modified compound)
- Sliding on DU GUIDE bush (compound obtained by sintering a state of spheroidal bronze on a suitably pressed mild steel strip and with subsequent impregnation and coating with a mixture of PTFE+FB)
- Scraper ring in SEALTHANE grade 9345 polyester resin
-Micrometic adjustment of spring pre-load via ring nuts
-Adjustment of hydraulic braking in extension pre-selectable on approximately 24 positions
-Double adjustment of the hydraulic compression braking, pre-selectable on approximately 10 positions each, separate for low and high speed
-Special oil with low viscosity and practically insensitive to temperature variations
-External compensation tank which allows an increase in the quantity of internal fluids
- Wheelbase adjustment of 25 mm (only for rear shock absorber)
- Wheelbase: rear 321 + 25 mm - front 181 mm
-Stroke: rear 62 mm - front 45 mm
Pair of Malossi shock absorbers for:
Pair of Malossi shock absorbers for Piaggio Quartz 50 2T LC.
Pair of Malossi shock absorbers for Piaggio Zip SP 50 2T LC 2001->.
Pair of Malossi shock absorbers for Piaggio Zip SP 50 2T LC <-2000.
Reference: 5911988
Brand: Malossi
Camshaft Malossi power cam 5911988. The Malossi camshaft was designed and built to give your scooter a purely sporty character that will allow you to maneuver easily in city traffic and to tackle long distances at high cruising speeds; the significant increase in torque will allow you truly formidable acceleration and hill climbing. NB: ONLY for Malossi...
Reference: 177.0093
Brand: POLINI
Polini fuel system for Mbk Booster 21 mm. Polini Code: 177.0093 SUPER COMPLETE KIT Ø21 For scooters equipped with the vertical Yamaha Minarelli engine, Polini Motori has prepared a super fuel system The heart of the power supply kit is the innovative CP Polini Ø21 carburettor complete with manifold, reed valve with 4 petals, air filter oversized, choke...
Reference: 01.TE.0024.L
Brand: Ohvale
M8 Washer Wide Band Ohvale. Ohvale code: 01.TE.0024.L
Reference: 174.2073
Brand: POLINI
Polini sintered brake pads 40x86x10.5 mm Code: 174.2073 Application: Honda, Honda Foresight 250 99, Honda Pantheon 125 Inject / 150 Inject, Peugeot, Peugeot SV 250 (HONDA)
Reference: 31 9879
Brand: Malossi
Malossi cast iron cylinder kit diameter 47 with 12 diameter pin for Honda X8R X - X8R S 2T 50 cc Malossi code: 31 9879 Malossi cylinder kit for HONDA XBR X - XBR S 50 2T
Reference: Carb.Cs.viol
Brand: CS Racing
Violet carburettor racing department Cs racing. Available Cs racing carburettor in the following sizes: Cs racing 15 VIOLET carburettor Cs racing 21 VIOLET carburettor Cs racing 23 VIOLET carburettor ATTENTION: HAND MADE TO ORDER, DELIVERY 90 DAYS!
Reference: 6215017BS
Brand: Malossi
Malossi MHR Synt approved brake pads Malossi code: 6215017BS Malossi brake pads for APRILIA RS 50 2T LC euro 2 from 2006 Front APPROVED Malossi brake pads for DERBI GP1 REVOLUTION 50 2T LC Front APPROVED Malossi brake pads for DERBI GPR NUDE 50 2T LC until 2005 Front APPROVED Malossi brake pads for DERBI GPR NUDE 50 2T LC from 2006 Front APPROVED Malossi...
Reference: 317.0111
Brand: POLINI
Series of Polini studs and cylinder nuts diameter 7x158 mm. Polini Code: 317.0111 Series of Polini studs and cylinder nuts for: Vespa, Vespa 125
Reference: 5217808
Brand: Malossi
Complete clutch Malossi Power Up clutch system 5217808 for Vespa Px Malossi code: 5217808 Complete clutch Malossi Power Up clutch system for clutch bell diameter 98 mm.
Reference: WPA479
Brand: CAPIT
Compact and resistant 5000mAh power bank battery, capable of guaranteeing 2/3 hours of continuous heating (WPA479). Only for women's white vest. Double USB port with fast charge (Fast-Charge) that can be used simultaneously to charge the mobile phone. Compatible with all USB devices. Capit Code: 18620
Reference: 0717122B
Brand: Malossi
Malossi stator fixing flange diameter 105 mm 0717122B Malossi code: 0717122B Malossi stator fixing flange diameter 105 mm for Power ignition for Piaggio mopeds.
Reference: A263
Brand: Alfano
22 mm adapter for Alfano A263 temperature sensor. This adapter must be used with sensors: A2101 / A2111 / A2152.
Reference: 01.IF.0092.L
Brand: Ohvale
Ohvale Complete brake lever Code: 01.IF.0092.L
Reference: 01.PE.0006.L
Brand: Ohvale
Ohvale Gp-0 Gp-2 footboard buffer. Ohvale code: 01.PE.0006.L Nylon footrest pad complete with fixing screw, compatible for: Ohvale Gp-0 footboard buffer. Ohvale Gp-2 footboard buffer.
Reference: 3618910B
Brand: Malossi
Malossi Multiple Gearbox Safety Ring for Vespa 3618910B Malossi Code: 3618910B
Reference: 5312280
Brand: Malossi
Malossi Rhq crankshaft 5312280 Malossi code: 5312280 Malossi Rhq crankshaft with 12 mm diameter pin and 39 mm stroke.
Pair of front and rear shock absorbers Malossi Rs24 4614479 for Piaggio
Malossi code: 4614479
Pair of Malossi shock absorbers, front wheelbase 180 mm and rear wheelbase 290 mm
10" tire shock absorbers
These special shock absorbers have technical characteristics that represent the maximum technological expression available on the market today:
-Type: hydropneumatic shock absorber with separate compensation tank
-Use: racing scooter
-Shock absorber rod Ø 14 mm in 38 NiCrMo4UNI 7845 hardened and tempered steel with hard chrome deposit 25-30 micron thick (surface hardness of the shaft not yet treated HRC 55/60)
-Piston Ø 36 mm with two independent disc packs, one in compression and one in extension
-New lamellar system in harmonic steel which allows for very precise calibration
-Piston guide shoe of the LUBRIFLON-PTFEB70 type (bronze filled modified compound)
- Sliding on DU GUIDE bush (compound obtained by sintering a state of spheroidal bronze on a suitably pressed mild steel strip and with subsequent impregnation and coating with a mixture of PTFE+FB)
- Scraper ring in SEALTHANE grade 9345 polyester resin
-Micrometic adjustment of spring pre-load via ring nuts
-Adjustment of hydraulic braking in extension pre-selectable on approximately 24 positions
-Double adjustment of the hydraulic compression braking, pre-selectable on approximately 10 positions each, separate for low and high speed
-Special oil with low viscosity and practically insensitive to temperature variations
-External compensation tank which allows an increase in the quantity of internal fluids
- Wheelbase adjustment of 25 mm (only for rear shock absorber)
- Wheelbase: rear 321 + 25 mm - front 181 mm
-Stroke: rear 62 mm - front 45 mm